1941 WILLYS CHASSIS
Because your chassis is the backbone of your street rod, LRS prides itself in fabricating one of the finest quality street rod frames in the industry. Our frames are uniquely fabricated from flat 11 gauge P&O plate. This allows us to weld the body mounting nuts inside the frame rails instead of using nut zerks that others use. We have our pieces laser cut so we are ensured of getting the same piece each time. We then fit the pieces on our rail jigs, square them and weld. All welds are then ground and inspected to verify that they have complete penetration and no porosity. They are then sanded with 50 grit to prep it for finishing. The rails are placed into our rotisserie frame fixture and tack welded to the fixture to eliminate movement while the frame is constructed and T.I.G. welded. Sounds like a lot of work? Yes, it is, but this is the way we choose to build your quality chassis. From start to finish, it takes 6 to 7 days to complete, depending on the number of coffee and smoke breaks we take! Many options are available for your completed chassis. Below are just a few ways to order; however, please feel free to call us with any other ideas you may have. We look forward to doing business with you. Please note that our completed chassis prices include many options that other shops do not.
Shown above with Heidt's front IFS frame members
Shown above is our center tubular cross member with removable transmission mount
This picture shows that our transmission mount accepts 350/PG, 400 Turbo and the 700 R4 all on one mount
This picture shows our rear 4-bar bracket and panhard bracket
Body/Chassis Package
(Pro Street or Hi Tec)
$ 20,000.00
Perimeter frame, complete Heidt's Superride II front end, tubular motor mounts, complete power brake assembly, rear 4 bar, rear panhard bar, rear housing with SVO disc brakes with e-brake, posi 3rd member (any ratio), rear coil over shocks.
Body includes hand laid fiberglass using ISO thermal tooling resin, complete floor and transmission tunnel, fenders and dash installed, doors and trunk lid hung and latched, hidden door hinges, bearclaw door latches, Lokar trunk lid release cable installed, aluminum trunk hinges, power windows installed, all glass included, wood kit installed, steel reinforced inner structure.
Complete Chassis
(Pro Street or Hi Tec)
$ 10,303.00
Perimeter frame, complete Heidt's Superride II front end, tubular engine mounts, complete power brake assembly, rear 4 bar, rear panhard bar, rear housing with SVO disc brakes with e-brake, posi 3rd member (any ratio), rear coil over shocks.
Perimeter Chassis
HiTec or Prostreet
Center Tubular Cross Member with removable transmission mount
Rear Coil-Over Bar
(no front cross member)
$ 3,150.00
Options
(Installed Prices, T.I.G. welded to chassis where applicable)
| Complete Heidt's Superride II Front End | $ 2,600.00 |
| Tubular Motor Mounts | 175.00 |
| Complete Power Brake Assembly (mount, booster, master cylinder and pedal) | 425.00 |
| Brake & Hydraulic Clutch Assembly (complete) | 472.00 |
| Rear 4-Bar | 490.00 |
| Rear Panhard Bar | 150.00 |
| Rear 9" Housing Cut to Size (axles, seals, bearings, bolts, round back) | 780.00 |
| Rear 9" Housing with Drum | 1,175.00 |
| Rear 9" Housing with Disc | 1,310.00 |
| 3rd Member Open (any ratio) | 750.00 |
| 3rd Member Posi (any ratio) | 1025.00 |
| Rear Coil-Over Shocks | 390.00 |
| Polished | 450.00 |
| Polished/Chrome Springs | 570.00 |
| Steel Brake Lines (w/AN fittings) | 738.00 |
Shipping and Crating Charges Additional
Prices & Design Subject to Change Without Notice
Ph: 417-466-4883
Fax: 417-466-2556